The cost of biscuit making machine lines is set by the line as a whole: its capacity, its width, its forming section, its oven and the scope of supply around it. Two quotations that look alike can describe very different plants. This article explains the decisions that move the investment, so that quotations can be compared on the same basis.

What decides the cost of a biscuit making machine?

Five decisions set the cost of an industrial biscuit making machine: capacity, working width, forming section, oven and scope of supply. Change any one and the investment changes, along with the cost of every tonne the line makes afterwards.

Capacity and width set the size of every machine on the line. The forming section depends on the product: a rotary moulder for soft dough, or sheeting, laminating and cutting for hard dough. The oven depends on the fuel available at the site. Sunbeam offers electric, oil, natural gas and LPG firing on its soft dough lines. Scope decides how much of the plant arrives under one contract.

Cost driverWhat it changesQuestion to ask the supplier
CapacitySize of every machine and the oven lengthIs capacity stated as saleable output per shift or as a rated peak?
Working widthOutput per metre of line and floor areaWhat output does one width step up add, in the same building?
Forming sectionMachines needed between mixer and ovenCan the line run soft and hard dough, and how long is the changeover?
Oven and fuelEnergy cost for the life of the lineWhich fuels can the oven run on, and how many heating zones does it have?
Scope of supplyWhat is included, integrated or left to the buyerIs there a written scope matrix with the quotation?

Why is capacity the first cost decision?

Capacity decides the size of everything else, so it is the decision that most changes the investment. It should be set from saleable output per shift, because rated capacity overstates what a line delivers in practice.

How to Size a Biscuit Linerecommends planning at 70 to 85 percent of rated capacity across a shift. In its worked example, twelve tonnes a day across two shifts needs roughly 1,000 kg/hr, not 750. Buying too far beyond need has its own cost, because an underloaded oven wastes fuel. The article's advice is one size step up, not two.

How does line width change the cost per tonne?

A wider line adds output without adding a new building, supervisor or maintenance routine, so the cost of each tonne usually falls. Moving from 1,220 mm to 1,525 mm gives around 25 percent more output in the same footprint.

That figure, from The Case for a Wider Line, comes from a 2008 project in eastern India. A planned 1,220 mm hard dough line became a 1,525 mm forming section, which has run the same savoury cracker for over eighteen years. Width is the wrong choice in three cases: the building cannot take it, demand for one product family will not use the output, or the packing line cannot keep pace.

What does a changeover cost a biscuit plant?

A changeover costs the output the line would have made while it was stopped, plus the waste on run-down and run-up. At 1,000 kg/hr, a four-hour changeover loses four tonnes of biscuits.

What a Changeover Actually Costs sets out four hidden costs: lost hours, out-of-spec product, production runs that never get scheduled, and dependence on a few skilled operators. Changing between hard and soft dough on a conventional plant can take much of a shift. A flexi line does it in about 15 minutes.

What sits outside the machinery quotation?

A machinery quotation rarely covers the whole plant, because building and foundation works, fuel and power supply, shipping, customs, travel, warranty and support terms are agreed separately. The plant budget has to include all of them.

Sunbeam's turnkey solutions include a written scope matrix with every quotation. It shows which items Sunbeam supplies, which it integrates, and which the buyer provides. Asking every supplier for the same matrix is the simplest way to compare quotations on equal terms. The documents to send are listed in What to Put in a Machinery RFQ.

How do you compare biscuit machine quotations fairly?

Compare quotations on saleable output per shift, scope of supply and changeover time, not on the headline figure. A quotation that looks lower can describe a narrower line, a rated rather than saleable capacity, or a scope that leaves more for the buyer to arrange.

Ask each supplier for drawings and full specification sheets with the quotation. Sunbeam issues these as standard for its hard dough lines and soft dough lines. Then put the five questions in the table above to every supplier.

Written by the engineers who design and commission Sunbeam biscuit lines. Sunbeam has designed and manufactured biscuit machinery in Bollaram, Hyderabad, since 1993, with installations across India, Africa and the Middle East.

Tell us what biscuit you produce, the capacity you require and the space available in your plant. Discuss your requirements with an engineer.